Products

About Us

Knowledge Center

Accessories

Terms of Use

Featured Products

Site Map

Videos

Contact Us

Dual-axis Pitch and Roll Stage

Home   > Motorized Pitch and Roll Stages  

Photo


Photo

The precise measurements of angles and the curvature of objects are easily determined using OES' Pitch and Roll Stages.   The Pitch axis (lower stage) is a high precision goniometer stage which features preloaded cross roller guides and a 1 to 296 ratio worm drive for smooth motion over a range of travel of +/- 45 degrees and has a typical accuracy of 0.05 degrees and repeatability of +/- 0.01 degrees.

The roll axis (upper stage) is also a high precision goniometer stage featuring preloaded cross roller guides and a 1:352 gear ratio worm drive for smooth motion over a range of travel of +/- 10 degrees. This stage has a 65 mm x 65 mm table and also has a typical accuracy of 0.05 degrees and repeatability of +/- 0.01 degrees. Additionally, each axis has end-of-travel limit switches. 

The PR120-45-10-01 and the PR120-45-10-04 which has Optical Encoders for position verification, are both stepper motor driven.  The PR120-45-10-02 is driven by Three Phase Servo motors and the PR120-45-10-03 is driven by DC Servo motors; and each have Quardrature Incremental Encoders for the higher speeds, resolution, and repeatability of closed loop servo systems.

Each axis features an adjustable calibrated scale to visually display the angle of rotation. The maximum speed with stepper motors is 14 degrees/second and 45 degrees/second with servo motors. The resolution of the PR120-45-10 stepper motor driven duel-axis stage depends on the resolution of the stepper motor driver resolution or the optical encoder if a servo motor is used. A resolution of 0.001 degrees equivalent to 3.6 arc-sec can be achieved using a 10 micro-steps per step stepper motor driver or an encoder with a resolution of 500 cycles per revolution.

The Dual-axis Pitch and Roll Stages require a Motion Controller that can be ordered as a complete plug-and-play system with joystick, trackball, and keypad.

Specifications

Type

PR120-45-10

DB9 Male pinout

Stepper Motor

Typical Phase Resistance 3.8 Ohms,  Bi-directional
Typical Phase Current 1 Amp
DB-9 Male Connector
Pin Assignment and Description

1

+5 VDC

2

CCW Limit Switch , Open Collector, Normally Open, Needs Pull up Resistor

3

CW Limit Switch, Open Collector , Normally Open, Needs Pull up Resistor

4

Common

5

Not Connected

6 Stepper Motor Phase A+
7 Stepper Motor Phase A-
8 Stepper Motor Phase B+
9 Stepper Motor Phase B-
 

Roll Axis

Structure Description Range of Travel

+/-10 degrees

Table Size 65 mm x 65 mm
Gear Ratio 1 degrees (stage) : 352 degrees (motor)
Height of Rotation Stage 75 mm
Drive Mechanism Worm Gear
Travel Guide Crossed-roller Guide
Rotation Center Deflection Accuracy +/-0.2 mm

Typical Accuracy

Resolution 0.001 degrees = 3.6 arcsec (10 Micro-steps per Step Motor Driver in use)
Repeatability +/-0.01 degrees
Positional Accuracy 0.05 degrees
Maximum Speed with Stepper Motor 14 degrees per second
Maximum Speed with Servo Motor 45 degrees per second 
Typical Stepper Motor Phase Current 1 .0 Amp
 

Pitch Axis

Structure Description Range of Travel

+/-45 degrees

   
Gear Ratio 1 degrees (stage) : 296 degrees (motor)
   
Drive Mechanism Worm Gear
Travel Guide Crossed-roller Guide
   

Typical Accuracy

Resolution 0.001 degrees = 3.6 arcsec (10 Micro-steps per Step Motor Driver in use)
Repeatability +/-0.01 degrees
Positional Accuracy 0.05 degrees
Maximum Speed with Stepper Motor 14 degrees per second
Maximum Speed with Servo Motor 45 degrees per second 
Typical Stepper Motor Phase Current 1 .0 Amp

 

Stepper Motor Driven Mechanical Drawing (Roll Table)

Photo

 

Ordering Information

Part No. Description Amount
PR 120-45-10-01 Dual-axis Stepper Motor Driven Linear Pitch and Roll Stage, Table Size 65x65 mm Click to Get a Quote
PR 120-45-10-02 Dual-axis Three Phase Brushless Servo Motor with Quadrature Incremental Optical Encoder Driven Pitch and Roll Stage, Table Size 65x65 mm Click to Get a Quote
PR 120-45-10-03 DC Servo Motor with Quadrature Incremental Optical Encoder Driven Pitch and Roll Stage, Table Size 65x65 mm Click to Get a Quote
PR 120-45-10-04 Dual-axis Stepper Motor Driven Linear Pitch and Roll Stage with 500 Cycles per Revolution Quadrature Optical Encoders Mounted at the back of the Stepper Motors, Table Size 65x65 mm Click to Get a Quote

 

Related Products

Photo Motion Controllers

Sharing link:

 


 

Home | Products | Accessories | Knowledge Center | About Us | Terms of Use |Testimonials | Featured Products | Site Map | Videos | Contact Us

                    facebook X linkedin youtube                      

contact-us