|
| |
Motorized Single-axis Table
|
|
Home >
Motorized Linear
Actuators
>
Low Cost Linear
Single-axis Stages
|
|
|
|
This motorized positioning table is made of aluminum alloy with an elegant black anodized surface.
It provides 15 mm of travel at a Maximum Speed with Stepper Motor of 5 mm per second.
The drive mechanism is lead screw.
The bench size is 65 X 65 mm and has a body weight of 1.2 Kg.
The maximum load of this stage table is 10 Kg.
This linear stage is also available with a three phase brushless motor and Optical Encoder (-04 Version).
The knob mounted on the motor allows for manual adjustment. This knob may be replaced with an Optical Encoder (-04 Version) for precision position verification.
This stage requires a
Motion Controller
that can be ordered as a complete plug-and-play system with RS-232, USB, joystick and keypad control.
Video Demonstration |
|
Specifications
| Type |
AQ110-15 |
|
Structure
Description |
Travel |
15 mm |
| Table Size |
65 mm x 65 mm |
| Lead Screw Pitch |
1 mm per turn |
| Travel Guide |
High Precision Crossed Roller |
| DB-9 Male Connector
|
|
Two-Phase Stepper Motor |
|
Typical Phase Resistance
|
3.8 Ohms, Bi-directional |
| Typical Phase Current |
1 Amp |
| |
|
Pin Assignment and Description |
| 1 |
+5 VDC for the Limit Sensors |
| 2 |
Far End Limit Switch
Open Collector or Normally Open
Needs Pull up Resistor (typically
1000 Ohms)
Approximately 2.5 mm away from Far End Hard Stop
|
| 3 |
Near Motor Limit Switch
Open Collector or Normally Open
Needs Pull up Resistor (typically
1000 Ohms)
Approximately 2.5 mm away from Motor Side Hard Stop
|
| 4 |
Return for+5 VDC |
|
5 |
Not Connected |
|
6 |
Stepper Motor Phase A+ |
| 7 |
Stepper Motor Phase A- |
| 8 |
Stepper Motor Phase B+ |
| 9 |
Stepper Motor Phase B- |
|
| Body Material |
Aluminum Alloy |
| Surface Treatment |
Black Anodized |
| Load Capacity |
15 kg |
| Weight |
1.2 kg |
|
Typical Accuracy
|
Resolution |
Control Electronics Dependent, 0.5 microns with 10 Micro-steps per Step Motor Driver in use
0.25 microns with 20 Micro-steps per Step Motor Driver in use |
| Maximum Speed with Stepper Motor |
15 mm / sec |
| Maximum Speed with Servo Motor |
|
| Positioning Accuracy |
10 microns |
|
Accessories
Description
|
Positioning Repeatability |
5 microns |
| Optical Encoder (-04 Version) |
Three Phase Brushless Three Phase Brushless Servo Motor and Optical Encoder (-02 Version)
|
|
|
|
Ordering Information
|
Part No. |
Description |
Amount |
|
AQ110-15-01 |
Stepper Motor Driven Linear Single-axis Stage, Travel
: 15 mm |
Click to Get a Quote |
|
AQ110-15-02 |
Three Phase Brushless Servo Motor with Quadrature Incremental
Optical Encoder Driven Linear Single-axis Stage, Travel
: 15 mm |
Click to Get a Quote |
|
AQ110-15-03 |
DC Servo Motor with Quadrature Incremental
Optical Encoder Driven Linear Single-axis Stage |
Click to Get a Quote |
|
AQ110-15-04 |
Stepper Motor Driven
Linear Single-axis Stage with 500 Cycles per Revolution
Quadrature Optical Encoder Mounted at the back
of the Stepper Motor |
Click to Get a Quote |
|
|
